MIPA 1K UV PRIMER FILLER GREY 1 LITRE

Due to the system, storage causes phase separation of the material in the container.
This is specific to the product and can be removed by thorough mixing. Phase
separation may also happen when this product is kept in the gravity cup for a longer
period. Therefore, it is necessary to thoroughly stir the filler.
Drying:
UV LED-Light: approx. 5 min
Hg-Lamp (mercury vapour lamp) approx. 5 min
Direct sunlight: approx. 4 - 5 min, please observe: When drying with sunlight, the dry
film thickness of 80 µm must not be exceeded, otherwise through-drying problems
may occur.
Note:
Although, the use of very powerful lamps shortens the drying time, this sudden drying
can lead to severe coating damage such as wrinkling and cracking and/ or adhesion
problems. Therefore, it is strongly recommended not to use such lamps or to make
sure that the specified UV-drying times are observed.
When drying, consider also the time, which is needed to achieve full light power:
Hg-lamps (mercury vapour lamps) require a warm-up time of approx. 3 minutes and
manufacturer’s instructions must be observed respectively.
The recommended lamp distance to the object should be 20-30 cm.
If the light field of the UV LED-Light is too little to cover at once the filler surface to be
dried, the lamp must be moved overlapping the area already dried. Care must be
taken to ensure that all partial areas are irradiated sufficiently for a homogeneous
through drying of the entire surface.
The UV drying time depends generally on following factors:

• Lamp intensity and UV spectrum
• rate of wear of the illuminant
• lamp distance
• applied coat thickness
• size of the refinished area
  The recommended dry film thickness of 80 - 100 µm for 2 coats must be observed. If
  higher coat thicknesses are required (max. 150 µm), it is necessary to do an
  intermediate UV-drying after the application of the 2nd coat. When drying with LED
  lamps, especially in case of thicker layers, the drying time of 5 minutes must be
  observed or, if necessary, extended to ensure complete curing of the filler layer. By
  using mercury vapour lamps, which have a higher radiation intensity, the drying times
  can generally be reduced.
  Substrate preparation:
  The substrate must be clean, dry and free from grease. Sand slightly the surface and
  degrease with Mipa Silikonentferner. Remove non adhering old paintworks and
  primers.
  Sand aluminium and galvanized substrates with grain P 220, steel with P 120. After
  sanding clean again thoroughly with Mipa Silikonentferner.

We use FedEx for our delivery services for all online orders.

Our deliveries will only be delivered Monday to Friday ONLY.

Free delivery must be for value of goods before VAT rate and delivery charge.

All deliveries are sent SAME WORKING DAY if orders are placed before 11am.

We aim to dispatch all orders within 1 working day.

There will be times when we are out of stock of particular stock lines / quantity's but you will receive an email or phone call from a member of staff advising you of a timescale.

Once your order has been dispatched you will receive an automated email confirmation.

With international delivery's there might be a customs delay.

** UK - Mainland Delivery Chargers **

Our standard delivery is charged at £5.95 +VAT on all UK Mainland orders under 20Kg.

Over 20kg orders are charged at £12.95 +VAT on all UK Mainland orders.

Free delivery for orders over £100 apply to UK Mainland buyers.

** UK - Scotland Delivery Chargers **

Our standard day delivery is charged at £6.95 +VAT on all Scotland orders under 20Kg.

Our standard day delivery is charged at £14.95 +VAT on all Scotland orders over 20Kg.

Free delivery for orders over £100 apply to Scotland buyers.

** UK - Northern Ireland Delivery Chargers **

Our standard day delivery is charged at £9.50 +VAT on all Northern Ireland orders under 20Kg.

Our standard day delivery is charged at £14.95 +VAT on all Northern Ireland orders over 20Kg.

Free delivery for orders over £150 apply to Northern Ireland buyers.

Your item must be in its original packaging condition to be returned.
You must return the item within 14 days of your purchase.

1. Please email orders@bodicraftsupplies.co.uk to request a refund stating a reason for your return
2. Once we have approved your return you must return your package to:

Returns
Bodicraft Supplies Ltd
1 Chalk Hill
Watford
Hertfordshire
WD19 4BL

3. Include in your package a signed letter stating the reason for your return and a copy of the original receipt.
4. For all returns the customer must pay for return shipping costs.

** Restocking Fee **

All items are subject to a 15% restocking fee, this will be deducted from your refund.
We also do not refund the original shipping or return costs that you paid on the order.